IEEE8023-EtherLike-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, Counter64, org, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TruthValue FROM SNMPv2-TC ifIndex, InterfaceIndex FROM IF-MIB; ieee8023etherMIB MODULE-IDENTITY LAST-UPDATED "201304110000Z" -- April 11, 2013 ORGANIZATION "IEEE 802.3 working group" CONTACT-INFO "WG-URL: http://www.ieee802.org/3/index.html WG-EMail: STDS-802-3-MIB@LISTSERV.IEEE.ORG Contact: Howard Frazier Postal: 3151 Zanker Road San Jose, CA 95134 USA Tel: +1.408.922.8164 E-mail: hfrazier@broadcom.com" DESCRIPTION "The MIB module to describe generic objects for Ethernet-like network interfaces." REVISION "201304110000Z" -- April 11, 2013 DESCRIPTION "Revision, based on an earlier version in IEEE Std 802.3.1-2011." REVISION "201102020000Z" -- February 2, 2011 DESCRIPTION "Initial version, based on an earlier version published in RFC 3635." ::= { org ieee(111) standards-association-numbers-series-standards(2) lan-man-stds(802) ieee802dot3(3) ieee802dot3dot1mibs(1) 10 } ieee8023etherMIBObjects OBJECT IDENTIFIER ::= { ieee8023etherMIB 1 } -- the Ethernet-like Statistics group dot3StatsTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3StatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics for a collection of Ethernet-like interfaces attached to a particular system. There will be one row in this table for each Ethernet-like interface in the system." ::= { ieee8023etherMIBObjects 2 } dot3StatsEntry OBJECT-TYPE SYNTAX Dot3StatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics for a particular interface to an Ethernet-like medium." INDEX { dot3StatsIndex } ::= { dot3StatsTable 1 } Dot3StatsEntry ::= SEQUENCE { dot3StatsIndex InterfaceIndex, dot3StatsAlignmentErrors Counter32, dot3StatsFCSErrors Counter32, dot3StatsSingleCollisionFrames Counter32, dot3StatsMultipleCollisionFrames Counter32, dot3StatsSQETestErrors Counter32, dot3StatsDeferredTransmissions Counter32, dot3StatsLateCollisions Counter32, dot3StatsExcessiveCollisions Counter32, dot3StatsInternalMacTransmitErrors Counter32, dot3StatsCarrierSenseErrors Counter32, dot3StatsFrameTooLongs Counter32, dot3StatsInternalMacReceiveErrors Counter32, dot3StatsSymbolErrors Counter32, dot3StatsDuplexStatus INTEGER, dot3StatsRateControlAbility TruthValue, dot3StatsRateControlStatus INTEGER, dot3StatsMaxFrameLength INTEGER } dot3StatsIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index value that uniquely identifies an interface to an Ethernet-like medium. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex." REFERENCE "IETF RFC 2863, ifIndex" ::= { dot3StatsEntry 1 } dot3StatsAlignmentErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. This counter does not increment for group encoding schemes greater than 4 bits per group. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsAlignmentErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.7, aAlignmentErrors" ::= { dot3StatsEntry 2 } dot3StatsFCSErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. This count does not include frames received with frame-too-long or frame-too-short error. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. Note: Coding errors detected by the Physical Layer for speeds above 10 Mb/s will cause the frame to fail the FCS check. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsFCSErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.6, aFrameCheckSequenceErrors." ::= { dot3StatsEntry 3 } dot3StatsSingleCollisionFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames that are involved in a single collision, and are subsequently transmitted successfully. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsMultipleCollisionFrames object. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.3, aSingleCollisionFrames." ::= { dot3StatsEntry 4 } dot3StatsMultipleCollisionFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames that are involved in more than one collision and are subsequently transmitted successfully. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.4, aMultipleCollisionFrames." ::= { dot3StatsEntry 5 } dot3StatsSQETestErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of times that the SQE TEST ERROR is received on a particular interface. The SQE TEST ERROR is set in accordance with the rules for verification of the SQE detection mechanism in the PLS Carrier Sense Function as described in IEEE Std 802.3, 7.2.4.6. This counter does not increment on interfaces operating at speeds greater than 10 Mb/s, or on interfaces operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 7.2.4.6, also 30.3.2.1.4, aSQETestErrors." ::= { dot3StatsEntry 6 } dot3StatsDeferredTransmissions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames for which the first transmission attempt on a particular interface is delayed because the medium is busy. The count represented by an instance of this object does not include frames involved in collisions. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.9, aFramesWithDeferredXmissions." ::= { dot3StatsEntry 7 } dot3StatsLateCollisions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times that a collision is detected on a particular interface later than one slotTime into the transmission of a packet. A (late) collision included in a count represented by an instance of this object is also considered as a (generic) collision for purposes of other collision-related statistics. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.10, aLateCollisions." ::= { dot3StatsEntry 8 } dot3StatsExcessiveCollisions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames for which transmission on a particular interface fails due to excessive collisions. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.11, aFramesAbortedDueToXSColls." ::= { dot3StatsEntry 9 } dot3StatsInternalMacTransmitErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames for which transmission on a particular interface fails due to an internal MAC sublayer transmit error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the dot3StatsLateCollisions object, the dot3StatsExcessiveCollisions object, or the dot3StatsCarrierSenseErrors object. The precise meaning of the count represented by an instance of this object is implementation- specific. In particular, an instance of this object may represent a count of transmission errors on a particular interface that are not otherwise counted. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsInternalMacTransmitErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.12, aFramesLostDueToIntMACXmitError." ::= { dot3StatsEntry 10 } dot3StatsCarrierSenseErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame on a particular interface. The count represented by an instance of this object is incremented at most once per transmission attempt, even if the carrier sense condition fluctuates during a transmission attempt. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.13, aCarrierSenseErrors." ::= { dot3StatsEntry 11 } -- { dot3StatsEntry 12 } is not assigned dot3StatsFrameTooLongs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received on a particular interface that exceed the maximum permitted frame size. The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. For interfaces operating at 10 Gb/s, this counter can roll over in less than 80 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsFrameTooLongs object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.25, aFrameTooLongErrors." ::= { dot3StatsEntry 13 } -- { dot3StatsEntry 14 } is not assigned -- { dot3StatsEntry 15 } is not assigned dot3StatsInternalMacReceiveErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames for which reception on a particular interface fails due to an internal MAC sublayer receive error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the dot3StatsFrameTooLongs object, the dot3StatsAlignmentErrors object, or the dot3StatsFCSErrors object. The precise meaning of the count represented by an instance of this object is implementation- specific. In particular, an instance of this object may represent a count of receive errors on a particular interface that are not otherwise counted. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsInternalMacReceiveErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.15, aFramesLostDueToIntMACRcvError." ::= { dot3StatsEntry 16 } dot3StatsSymbolErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "For an interface operating at 100 Mb/s, the number of times there was an invalid data symbol when a valid carrier was present. For an interface operating in half-duplex mode at 1000 Mb/s, the number of times the receiving media is non-idle (a carrier event) for a period of time equal to or greater than slotTime, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Data reception error' or 'carrier extend error' on the GMII. For an interface operating in full-duplex mode at 1000 Mb/s, the number of times the receiving media is non-idle (a carrier event) for a period of time equal to or greater than minFrameSize, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Data reception error' on the GMII. For an interface operating at 10 Gb/s, 40 Gb/s, and 100 Gb/s, it is a count of the number of times the receiving media is non-idle (the time between the Start of Packet Delimiter and the End of Packet Delimiter) for a period of time equal to or greater than minFrameSize, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Receive Error' on the XGMII, the XLGMII, or the CGMII. The count represented by an instance of this object is incremented at most once per carrier event, even if multiple symbol errors occur during the carrier event. This count does not increment if a collision is present. This counter does not increment when the interface is operating at 10 Mb/s. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsSymbolErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.2.1.5, aSymbolErrorDuringCarrier." ::= { dot3StatsEntry 17 } dot3StatsDuplexStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), halfDuplex(2), fullDuplex(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current mode of operation of the MAC entity. 'unknown' indicates that the current duplex mode could not be determined. Management control of the duplex mode is accomplished through the MAU MIB. When an interface does not support autonegotiation, or when autonegotiation is not enabled, the duplex mode is controlled using ifMauDefaultType. When autonegotiation is supported and enabled, duplex mode is controlled using ifMauAutoNegAdvertisedBits. In either case, the currently operating duplex mode is reflected both in this object and in ifMauType. Note that this object provides redundant information with ifMauType. Normally, redundant objects are discouraged. However, in this instance, it allows a management application to determine the duplex status of an interface without having to know every possible value of ifMauType. This was felt to be sufficiently valuable to justify the redundancy." REFERENCE "IEEE Std 802.3, 30.3.1.1.32, aDuplexStatus." ::= { dot3StatsEntry 18 } dot3StatsRateControlAbility OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "'true' for interfaces operating at speeds above 1000 Mb/s that support Rate Control through lowering the average data rate of the MAC sublayer, with frame granularity, and 'false' otherwise." REFERENCE "IEEE Std 802.3, 30.3.1.1.33, aRateControlAbility." ::= { dot3StatsEntry 19 } dot3StatsRateControlStatus OBJECT-TYPE SYNTAX INTEGER { rateControlOff(1), rateControlOn(2), unknown(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current Rate Control mode of operation of the MAC sublayer of this interface." REFERENCE "IEEE Std 802.3, 30.3.1.1.34, aRateControlStatus." ::= { dot3StatsEntry 20 } dot3StatsMaxFrameLength OBJECT-TYPE SYNTAX INTEGER { unknown(1), baseFrame(2), qTaggedFrame(3), envelopeFrame(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the MAC frame length at which the dot3StatsFrameTooLongs counter is incremented." REFERENCE "IEEE Std 802.3, 30.3.1.1.37, aMaxFrameLength." ::= { dot3StatsEntry 21 } -- the Ethernet-like Collision Statistics group -- Implementation of this group is optional; it is appropriate -- for all systems which have the necessary metering dot3CollTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3CollEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A collection of collision histograms for a particular set of interfaces." REFERENCE "IEEE Std 802.3, 30.3.1.1.30, aCollisionFrames." ::= { ieee8023etherMIBObjects 5 } dot3CollEntry OBJECT-TYPE SYNTAX Dot3CollEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A cell in the histogram of per-frame collisions for a particular interface. An instance of this object represents the frequency of individual MAC frames for which the transmission (successful or otherwise) on a particular interface is accompanied by a particular number of media collisions." INDEX { ifIndex, dot3CollCount } ::= { dot3CollTable 1 } Dot3CollEntry ::= SEQUENCE { dot3CollCount Integer32, dot3CollFrequencies Counter32 } -- { dot3CollEntry 1 } is no longer in use dot3CollCount OBJECT-TYPE SYNTAX Integer32 (1..16) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The number of per-frame media collisions for which a particular collision histogram cell represents the frequency on a particular interface." ::= { dot3CollEntry 2 } dot3CollFrequencies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of individual MAC frames for which the transmission (successful or otherwise) on a particular interface occurs after the frame has experienced exactly the number of collisions in the associated dot3CollCount object. For example, a frame which is transmitted on interface 77 after experiencing exactly 4 collisions would be indicated by incrementing only dot3CollFrequencies.77.4. No other instance of dot3CollFrequencies would be incremented in this example. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { dot3CollEntry 3 } dot3ControlTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3ControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of descriptive and status information about the MAC Control sublayer on the Ethernet-like interfaces attached to a particular system. There will be one row in this table for each Ethernet-like interface in the system which implements the MAC Control sublayer. If some, but not all, of the Ethernet-like interfaces in the system implement the MAC Control sublayer, there will be fewer rows in this table than in the dot3StatsTable." ::= { ieee8023etherMIBObjects 9 } dot3ControlEntry OBJECT-TYPE SYNTAX Dot3ControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing information about the MAC Control sublayer on a single Ethernet-like interface." INDEX { dot3StatsIndex } ::= { dot3ControlTable 1 } Dot3ControlEntry ::= SEQUENCE { dot3ControlFunctionsSupported BITS, dot3ControlInUnknownOpcodes Counter32, dot3HCControlInUnknownOpcodes Counter64 } dot3ControlFunctionsSupported OBJECT-TYPE SYNTAX BITS { pause(0), -- 802.3 pause flow control mpcp(1), -- 802.3 multi-point control protocol pfc(2) -- 802.3 priority-based flow control } MAX-ACCESS read-only STATUS current DESCRIPTION "A list of the possible MAC Control functions implemented for this interface." REFERENCE "IEEE Std 802.3, 30.3.3.2, aMACControlFunctionsSupported." ::= { dot3ControlEntry 1 } dot3ControlInUnknownOpcodes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of MAC Control frames received on this interface that contain an opcode that is not supported by this device. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCControlInUnknownOpcodes object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.3.5, aUnsupportedOpcodesReceived" ::= { dot3ControlEntry 2 } dot3HCControlInUnknownOpcodes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of MAC Control frames received on this interface that contain an opcode that is not supported by this device. This counter is a 64-bit version of dot3ControlInUnknownOpcodes. It should be used on interfaces operating at 10 Gb/s or faster. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.3.5, aUnsupportedOpcodesReceived" ::= { dot3ControlEntry 3 } dot3PauseTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3PauseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of descriptive and status information about the MAC Control PAUSE function on the Ethernet-like interfaces attached to a particular system. There will be one row in this table for each Ethernet-like interface in the system which supports the MAC Control PAUSE function (i.e., the 'pause' bit in the corresponding instance of dot3ControlFunctionsSupported is set). If some, but not all, of the Ethernet-like interfaces in the system implement the MAC Control PAUSE function (for example, if some interfaces only support half-duplex), there will be fewer rows in this table than in the dot3StatsTable." ::= { ieee8023etherMIBObjects 10 } dot3PauseEntry OBJECT-TYPE SYNTAX Dot3PauseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing information about the MAC Control PAUSE function on a single Ethernet-like interface." INDEX { dot3StatsIndex } ::= { dot3PauseTable 1 } Dot3PauseEntry ::= SEQUENCE { dot3PauseAdminMode INTEGER, dot3PauseOperMode INTEGER, dot3InPauseFrames Counter32, dot3OutPauseFrames Counter32, dot3HCInPauseFrames Counter64, dot3HCOutPauseFrames Counter64 } dot3PauseAdminMode OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabledXmit(2), enabledRcv(3), enabledXmitAndRcv(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the default administrative PAUSE mode for this interface. This object represents the administratively-configured PAUSE mode for this interface. If Auto-Negotiation is not enabled or is not implemented for the active MAU attached to this interface, the value of this object determines the operational PAUSE mode of the interface whenever it is operating in full-duplex mode. In this case, a set to this object will force the interface into the specified mode. If Auto-Negotiation is implemented and enabled for the MAU attached to this interface, the PAUSE mode for this interface is determined by Auto-Negotiation, and the value of this object denotes the mode to which the interface will automatically revert if/when Auto-Negotiation is later disabled. Note that when Auto-Negotiation is running, administrative control of the PAUSE mode may be accomplished using the ifMauAutoNegCapAdvertisedBits object in the MAU-MIB module. Note that the value of this object is ignored when the interface is not operating in full-duplex mode. An attempt to set this object to 'enabledXmit(2)' or 'enabledRcv(3)' will fail on interfaces that do not support operation at greater than 100 Mb/s." ::= { dot3PauseEntry 1 } dot3PauseOperMode OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabledXmit(2), enabledRcv(3), enabledXmitAndRcv(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object reflects the PAUSE mode currently in use on this interface, as determined by either (1) the result of the Auto-Negotiation function or (2) if Auto-Negotiation is not enabled or is not implemented for the active MAU attached to this interface, by the value of dot3PauseAdminMode. Interfaces operating at 100 Mb/s or less will never return 'enabledXmit(2)' or 'enabledRcv(3)'. Interfaces operating in half-duplex mode will return 'disabled(1)'. Interfaces on which Auto-Negotiation is enabled but not yet completed should return the value 'disabled(1)'." ::= { dot3PauseEntry 2 } dot3InPauseFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of MAC Control frames received on this interface with an opcode indicating the PAUSE operation. This counter does not increment when the interface is operating in half-duplex mode. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCInPauseFrames object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.4.3, aPAUSEMACCtrlFramesReceived." ::= { dot3PauseEntry 3 } dot3OutPauseFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of MAC Control frames transmitted on this interface with an opcode indicating the PAUSE operation. This counter does not increment when the interface is operating in half-duplex mode. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCOutPauseFrames object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.4.2, aPAUSEMACCtrlFramesTransmitted." ::= { dot3PauseEntry 4 } dot3HCInPauseFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of MAC Control frames received on this interface with an opcode indicating the PAUSE operation. This counter does not increment when the interface is operating in half-duplex mode. This counter is a 64-bit version of dot3InPauseFrames. It should be used on interfaces operating at 10 Gb/s or faster. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.4.3, aPAUSEMACCtrlFramesReceived." ::= { dot3PauseEntry 5 } dot3HCOutPauseFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of MAC Control frames transmitted on this interface with an opcode indicating the PAUSE operation. This counter does not increment when the interface is operating in half-duplex mode. This counter is a 64-bit version of dot3OutPauseFrames. It should be used on interfaces operating at 10 Gb/s or faster. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.4.2, aPAUSEMACCtrlFramesTransmitted." ::= { dot3PauseEntry 6 } dot3HCStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3HCStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing 64-bit versions of error counters from the dot3StatsTable. The 32-bit versions of these counters may roll over quite quickly on higher speed Ethernet interfaces. The counters that have 64-bit versions in this table are the counters that apply to full-duplex interfaces, since 10 Gb/s and faster Ethernet-like interfaces do not support half-duplex, and very few 1000 Mb/s Ethernet-like interfaces support half-duplex. Entries in this table are recommended for interfaces capable of operating at 1000 Mb/s or faster, and are required for interfaces capable of operating at 10 Gb/s or faster. Lower speed Ethernet-like interfaces do not need entries in this table, in which case there may be fewer entries in this table than in the dot3StatsTable. However, implementations containing interfaces with a mix of speeds may choose to implement entries in this table for all Ethernet-like interfaces." ::= { ieee8023etherMIBObjects 11 } dot3HCStatsEntry OBJECT-TYPE SYNTAX Dot3HCStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing 64-bit statistics for a single Ethernet-like interface." INDEX { dot3StatsIndex } ::= { dot3HCStatsTable 1 } Dot3HCStatsEntry ::= SEQUENCE { dot3HCStatsAlignmentErrors Counter64, dot3HCStatsFCSErrors Counter64, dot3HCStatsInternalMacTransmitErrors Counter64, dot3HCStatsFrameTooLongs Counter64, dot3HCStatsInternalMacReceiveErrors Counter64, dot3HCStatsSymbolErrors Counter64, dot3HCStatsTransmitLPIMicroseconds Counter64, dot3HCStatsReceiveLPIMicroseconds Counter64, dot3HCStatsTransmitLPITransitions Counter64, dot3HCStatsReceiveLPITransitions Counter64 } dot3HCStatsAlignmentErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. This counter does not increment for group encoding schemes greater than 4 bits per group. This counter is a 64-bit version of dot3StatsAlignmentErrors. It should be used on interfaces operating at 10 Gb/s or faster. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.7, aAlignmentErrors" ::= { dot3HCStatsEntry 1 } dot3HCStatsFCSErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. This count does not include frames received with frame-too-long or frame-too-short error. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. Note: Coding errors detected by the Physical Layer for speeds above 10 Mb/s will cause the frame to fail the FCS check. This counter is a 64-bit version of dot3StatsFCSErrors. It should be used on interfaces operating at 10 Gb/s or faster. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.6, aFrameCheckSequenceErrors." ::= { dot3HCStatsEntry 2 } dot3HCStatsInternalMacTransmitErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames for which transmission on a particular interface fails due to an internal MAC sublayer transmit error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the dot3StatsLateCollisions object, the dot3StatsExcessiveCollisions object, or the dot3StatsCarrierSenseErrors object. The precise meaning of the count represented by an instance of this object is implementation- specific. In particular, an instance of this object may represent a count of transmission errors on a particular interface that are not otherwise counted. This counter is a 64-bit version of dot3StatsInternalMacTransmitErrors. It should be used on interfaces operating at 10 Gb/s or faster. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.12, aFramesLostDueToIntMACXmitError." ::= { dot3HCStatsEntry 3 } dot3HCStatsFrameTooLongs OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received on a particular interface that exceed the maximum permitted frame size. The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. This counter is a 64-bit version of dot3StatsFrameTooLongs. It should be used on interfaces operating at 10 Gb/s or faster. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.25, aFrameTooLongErrors." ::= { dot3HCStatsEntry 4 } dot3HCStatsInternalMacReceiveErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames for which reception on a particular interface fails due to an internal MAC sublayer receive error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the dot3StatsFrameTooLongs object, the dot3StatsAlignmentErrors object, or the dot3StatsFCSErrors object. The precise meaning of the count represented by an instance of this object is implementation- specific. In particular, an instance of this object may represent a count of receive errors on a particular interface that are not otherwise counted. This counter is a 64-bit version of dot3StatsInternalMacReceiveErrors. It should be used on interfaces operating at 10 Gb/s or faster. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.1.1.15, aFramesLostDueToIntMACRcvError." ::= { dot3HCStatsEntry 5 } dot3HCStatsSymbolErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "For an interface operating at 100 Mb/s, the number of times there was an invalid data symbol when a valid carrier was present. For an interface operating in half-duplex mode at 1000 Mb/s, the number of times the receiving media is non-idle (a carrier event) for a period of time equal to or greater than slotTime, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Data reception error' or 'carrier extend error' on the GMII. For an interface operating in full-duplex mode at 1000 Mb/s, the number of times the receiving media is non-idle (a carrier event) for a period of time equal to or greater than minFrameSize, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Data reception error' on the GMII. For an interface operating at 10 Gb/s, 40 Gb/s and 100 Gb/s, the number of times the receiving media is non-idle (a carrier event) for a period of time equal to or greater than minFrameSize, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Receive Error' on the XGMII, the XLGMII, or the CGMII. The count represented by an instance of this object is incremented at most once per carrier event, even if multiple symbol errors occur during the carrier event. This count does not increment if a collision is present. This counter is a 64-bit version of dot3StatsSymbolErrors. It should be used on interfaces operating at 10 Gb/s or faster. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.2.1.5, aSymbolErrorDuringCarrier." ::= { dot3HCStatsEntry 6 } dot3HCStatsTransmitLPIMicroseconds OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count reflecting the amount of time that the LPI_REQUEST parameter has the value ASSERT. The request is indicated to the PHY according to the requirements of the RS (see IEEE Std 802.3 22.7, 35.4, and 46.4). This counter has a maximum increment rate of 1 000 000 counts per second." REFERENCE "IEEE Std 802.3, 30.3.2.1.8 aTransmitLPIMicroseconds." ::= { dot3HCStatsEntry 7 } dot3HCStatsReceiveLPIMicroseconds OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count reflecting the amount of time that the LPI_INDICATION parameter has the value ASSERT. The indication reflects the state of the PHY according to the requirements of the RS (see IEEE Std 802.3 22.7, 35.4, and 46.4). This counter has a maximum increment rate of 1 000 000 counts per second." REFERENCE "IEEE Std 802.3, 30.3.2.1.9 aReceiveLPIMicroseconds." ::= { dot3HCStatsEntry 8 } dot3HCStatsTransmitLPITransitions OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of occurrences of the transition from state LPI_DEASSERTED to state LPI_ASSERTED of the LPI transmit state diagram is the RS. The state transition corresponds to the assertion of the LPI_REQUEST parameter. The request is indicated to the PHY according to the requirements of the RS (see IEEE Std 802.3 22.7, 35.4, 46.4.) This counter has a maximum increment rate of 50 000 counts per second at 100 Mb/s; 90 000 counts per second at 1000 Mb/s; and 230 000 counts per second at 10 Gb/s." REFERENCE "IEEE Std 802.3, 30.3.2.1.10 aTransmitLPITransitions." ::= { dot3HCStatsEntry 9 } dot3HCStatsReceiveLPITransitions OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of occurrences of the transition from DEASSERT to ASSERT of the LPI_INDICATE parameter. The indication reflects the state of the PHY according to the requirements of the RS (see IEEE Std 802.3 22.7, 35.4, and 46.4). This counter has a maximum increment rate of 50 000 counts per second at 100 Mb/s; 90 000 counts per second at 1000 Mb/s; and 230 000 counts per second at 10 Gb/s." REFERENCE "IEEE Std 802.3, 30.3.2.1.11 aReceiveLPITransitions." ::= { dot3HCStatsEntry 10 } dot3SlowProtocolFrameLimit OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of Slow Protocol frames of a given subtype that can be transmitted in a one second interval. The default value is 10." REFERENCE "IEEE Std 802.3, 30.3.1.1.38, aSlowProtocolFrameLimit." DEFVAL { 10 } ::= { ieee8023etherMIBObjects 12 } dot3ExtensionTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3ExtensionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of status information about the Extension MAC Control frames transmitted and received on the Ethernet-like interfaces attached to a particular system. There will be one row in this table for each Ethernet-like interface in the system which supports Extension MAC Control function (i.e., the 'mpcp' bit in the corresponding instance of dot3ControlFunctionsSupported is set). If some, but not all, of the Ethernet-like interfaces in the system implement the Extension MAC Control function, there will be fewer rows in this table than in the dot3StatsTable." ::= { ieee8023etherMIBObjects 13 } dot3ExtensionEntry OBJECT-TYPE SYNTAX Dot3ExtensionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing information about the Extension MAC Control function on a single Ethernet-like interface." INDEX { dot3StatsIndex } ::= { dot3ExtensionTable 1 } Dot3ExtensionEntry ::= SEQUENCE { dot3HCInExtensionFrames Counter64, dot3HCOutExtensionFrames Counter64, dot3ExtensionMacCtrlStatus Unsigned32 } dot3HCInExtensionFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Extension MAC Control frames received on this interface. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.8.2 aEXTENSIONMACCtrlFramesReceived." ::= { dot3ExtensionEntry 1 } dot3HCOutExtensionFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Extension MAC Control frames transmitted on this interface. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "IEEE Std 802.3, 30.3.8.1 aEXTENSIONMACCtrlFramesTransmitted." ::= { dot3ExtensionEntry 2 } dot3ExtensionMacCtrlStatus OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current EXTENSIONMACCtrlStatus as described in IEEE Std 802.3, 30.3.8.3." REFERENCE "IEEE Std 802.3, 30.3.8.3, aEXTENSIONMACCtrlStatus." ::= { dot3ExtensionEntry 3 } dot3PFCTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3PFCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of descriptive and status information about the MAC Control Priority-based Flow Control function on the Ethernet-like interfaces attached to a particular system. There will be one row in this table for each Ethernet-like interface in the system which supports the MAC Control PFC function (i.e., the 'pfc' bit in the corresponding instance of dot3ControlFunctionsSupported is set). If some, but not all, of the Ethernet-like interfaces in the system implement the MAC Control PFC function (for example, if some interfaces only support half-duplex), there will be fewer rows in this table than in the dot3StatsTable." ::= { ieee8023etherMIBObjects 14 } dot3PFCEntry OBJECT-TYPE SYNTAX Dot3PFCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing information about the MAC Control PFC function on a single Ethernet-like interface." INDEX { dot3StatsIndex } ::= { dot3PFCTable 1 } Dot3PFCEntry ::= SEQUENCE { dot3PFCAdminMode INTEGER, dot3PFCOperMode INTEGER, dot3HCInPFCFrames Counter64, dot3HCOutPFCFrames Counter64 } dot3PFCAdminMode OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the default administrative PFC mode for this interface. This object represents the administratively-configured PFC mode for this interface. The value of this object determines the operational PFC mode of the interface. A set to this object will force the interface into the specified mode. Note that the value of this object is ignored when the interface is not operating in full-duplex mode." ::= { dot3PFCEntry 1 } dot3PFCOperMode OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object reflects the PFC mode currently in use on this interface, as determined by by the value of dot3PFCAdminMode." REFERENCE "IEEE Std 802.3, 30.3.3.6 aPFCenableStatus" ::= { dot3PFCEntry 2 } dot3HCInPFCFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of MAC Control frames received on this interface with an opcode indicating the PFC operation. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { dot3PFCEntry 3 } dot3HCOutPFCFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of MAC Control frames transmitted on this interface with an opcode indicating the PFC operation. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { dot3PFCEntry 4 } -- { ieee8023etherMIBObjects 6 }, the dot3ChipSets tree, -- is defined in [RFC2666] -- Conformance statements etherConformance OBJECT IDENTIFIER ::= { ieee8023etherMIB 2 } etherGroups OBJECT IDENTIFIER ::= { etherConformance 1 } etherCompliances OBJECT IDENTIFIER ::= { etherConformance 2 } -- Compliance statements dot3Compliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for managed network entities which have Ethernet-like network interfaces. Note that compliance with this MIB module requires compliance with the ifCompliance3 MODULE-COMPLIANCE statement of the IF-MIB (IETF RFC 2863). In addition, compliance with this MIB module requires compliance with the mauModIfCompl3 MODULE-COMPLIANCE statement of the MAU-MIB module defined in Clause 13." MODULE -- this module MANDATORY-GROUPS { etherStatsBaseGroup2 } GROUP etherDuplexGroup DESCRIPTION "This group is mandatory for all Ethernet-like network interfaces which are capable of operating in full-duplex mode. It is highly recommended for all Ethernet-like network interfaces." GROUP etherRateControlGroup DESCRIPTION "This group is mandatory for all Ethernet-like network interfaces which are capable of operating at speeds faster than 1000 Mb/s. It is highly recommended for all Ethernet-like network interfaces." GROUP etherStatsLowSpeedGroup DESCRIPTION "This group is mandatory for all Ethernet-like network interfaces which are capable of operating at 10 Mb/s or slower in half-duplex mode." GROUP etherStatsHighSpeedGroup DESCRIPTION "This group is mandatory for all Ethernet-like network interfaces which are capable of operating at 100 Mb/s or faster." GROUP etherStatsHalfDuplexGroup DESCRIPTION "This group is mandatory for all Ethernet-like network interfaces which are capable of operating in half-duplex mode." GROUP etherHCStatsGroup DESCRIPTION "This group is mandatory for all Ethernet-like network interfaces which are capable of operating at 10 Gb/s or faster. It is recommended for all Ethernet-like network interfaces which are capable of operating at 1000 Mb/s or faster." GROUP etherControlGroup DESCRIPTION "This group is mandatory for all Ethernet-like network interfaces that support the MAC Control sublayer." GROUP etherHCControlGroup DESCRIPTION "This group is mandatory for all Ethernet-like network interfaces that support the MAC Control sublayer and are capable of operating at 10 Gb/s or faster." GROUP etherControlPauseGroup DESCRIPTION "This group is mandatory for all Ethernet-like network interfaces that support the MAC Control PAUSE function." GROUP etherHCControlPauseGroup DESCRIPTION "This group is mandatory for all Ethernet-like network interfaces that support the MAC Control PAUSE function and are capable of operating at 10 Gb/s or faster." GROUP etherCollisionTableGroup DESCRIPTION "This group is optional. It is appropriate for all Ethernet-like network interfaces which are capable of operating in half-duplex mode and have the necessary metering. Implementation in systems with such interfaces is highly recommended." GROUP etherHCStatsLpiGroup DESCRIPTION "This group is mandatory for all Ethernet-like network interfaces that support the Low Power Idle function." GROUP etherSlowProtocolsGroup DESCRIPTION "This group is optional. It is appropriate for Ethernet-like network interfaces that implement OAM as defined in Clause 57 of IEEE Std 802.3." GROUP etherExtensionMacCtrlGroup DESCRIPTION "This group is mandatory for all Ethernet-like network interfaces that implement Extension MAC Control." GROUP etherPfcGroup DESCRIPTION "This group is mandatory for all Ethernet-like network interfaces that implement Priority Flow Control." ::= { etherCompliances 1 } -- units of conformance etherCollisionTableGroup OBJECT-GROUP OBJECTS { dot3CollFrequencies } STATUS current DESCRIPTION "A collection of objects providing a histogram of packets successfully transmitted after experiencing exactly N collisions." ::= { etherGroups 1 } etherStatsLowSpeedGroup OBJECT-GROUP OBJECTS { dot3StatsSQETestErrors } STATUS current DESCRIPTION "A collection of objects providing information applicable to Ethernet-like network interfaces capable of operating at 10 Mb/s or slower in half-duplex mode." ::= { etherGroups 2 } etherStatsHighSpeedGroup OBJECT-GROUP OBJECTS { dot3StatsSymbolErrors } STATUS current DESCRIPTION "A collection of objects providing information applicable to Ethernet-like network interfaces capable of operating at 100 Mb/s or faster." ::= { etherGroups 3 } etherDuplexGroup OBJECT-GROUP OBJECTS { dot3StatsDuplexStatus } STATUS current DESCRIPTION "A collection of objects providing information about the duplex mode of an Ethernet-like network interface." ::= { etherGroups 4 } etherControlGroup OBJECT-GROUP OBJECTS { dot3ControlFunctionsSupported, dot3ControlInUnknownOpcodes } STATUS current DESCRIPTION "A collection of objects providing information about the MAC Control sublayer on Ethernet-like network interfaces." ::= { etherGroups 5 } etherControlPauseGroup OBJECT-GROUP OBJECTS { dot3PauseAdminMode, dot3PauseOperMode, dot3InPauseFrames, dot3OutPauseFrames } STATUS current DESCRIPTION "A collection of objects providing information about and control of the MAC Control PAUSE function on Ethernet-like network interfaces." ::= { etherGroups 6 } etherStatsBaseGroup2 OBJECT-GROUP OBJECTS { dot3StatsAlignmentErrors, dot3StatsFCSErrors, dot3StatsInternalMacTransmitErrors, dot3StatsFrameTooLongs, dot3StatsInternalMacReceiveErrors, dot3StatsMaxFrameLength } STATUS current DESCRIPTION "A collection of objects providing information applicable to all Ethernet-like network interfaces." ::= { etherGroups 7 } etherStatsHalfDuplexGroup OBJECT-GROUP OBJECTS { dot3StatsSingleCollisionFrames, dot3StatsMultipleCollisionFrames, dot3StatsDeferredTransmissions, dot3StatsLateCollisions, dot3StatsExcessiveCollisions, dot3StatsCarrierSenseErrors } STATUS current DESCRIPTION "A collection of objects providing information applicable only to half-duplex Ethernet-like network interfaces." ::= { etherGroups 8 } etherHCStatsGroup OBJECT-GROUP OBJECTS { dot3HCStatsAlignmentErrors, dot3HCStatsFCSErrors, dot3HCStatsInternalMacTransmitErrors, dot3HCStatsFrameTooLongs, dot3HCStatsInternalMacReceiveErrors, dot3HCStatsSymbolErrors } STATUS current DESCRIPTION "A collection of objects providing high-capacity statistics applicable to higher-speed Ethernet-like network interfaces." ::= { etherGroups 9 } etherHCControlGroup OBJECT-GROUP OBJECTS { dot3HCControlInUnknownOpcodes } STATUS current DESCRIPTION "A collection of objects providing high-capacity statistics for the MAC Control sublayer on higher-speed Ethernet-like network interfaces." ::= { etherGroups 10 } etherHCControlPauseGroup OBJECT-GROUP OBJECTS { dot3HCInPauseFrames, dot3HCOutPauseFrames } STATUS current DESCRIPTION "A collection of objects providing high-capacity statistics for the MAC Control PAUSE function on higher-speed Ethernet-like network interfaces." ::= { etherGroups 11 } etherRateControlGroup OBJECT-GROUP OBJECTS { dot3StatsRateControlAbility, dot3StatsRateControlStatus } STATUS current DESCRIPTION "A collection of objects providing information about the Rate Control function on Ethernet-like interfaces." ::= { etherGroups 12 } etherHCStatsLpiGroup OBJECT-GROUP OBJECTS { dot3HCStatsTransmitLPIMicroseconds, dot3HCStatsReceiveLPIMicroseconds, dot3HCStatsTransmitLPITransitions, dot3HCStatsReceiveLPITransitions } STATUS current DESCRIPTION "A collection of objects providing information about the Low Power Idle function on Ethernet-like interfaces." ::= { etherGroups 13 } etherSlowProtocolsGroup OBJECT-GROUP OBJECTS { dot3SlowProtocolFrameLimit } STATUS current DESCRIPTION "An object providing control and information about the frame transmission rate limit for Slow Protocols on Ethernet-like interfaces." ::= { etherGroups 14 } etherExtensionMacCtrlGroup OBJECT-GROUP OBJECTS { dot3HCInExtensionFrames, dot3HCOutExtensionFrames, dot3ExtensionMacCtrlStatus } STATUS current DESCRIPTION "A collection of objects providing information about the Extension MAC Control function on Ethernet-like interfaces." ::= { etherGroups 15 } etherPfcGroup OBJECT-GROUP OBJECTS { dot3PFCAdminMode, dot3PFCOperMode, dot3HCInPFCFrames, dot3HCOutPFCFrames } STATUS current DESCRIPTION "A collection of objects providing information about the Priority Flow Control function on Ethernet-like interfaces." ::= { etherGroups 16 } END