| Thread Links | Date Links | ||||
|---|---|---|---|---|---|
| Thread Prev | Thread Next | Thread Index | Date Prev | Date Next | Date Index |
|
Hi Frank, That is a very good summary.
Many of us try to explain these things to colleagues and what you have now given us is a written version of what for me has involved a lot of white board writing and hand waving. One point that has crept in with PAM4 PMDs is that not all of the path penalty is captured by TDECQ.
There are additional penalties for MPI (multipath interference) and DGD penalty.
So in the link budget for the 100Gbps per wavelength PMDs we have allocated additional link budget of 0.3 to 0.5 dB for these impairments. Regards, David Lewis From: Frank J Effenberger <frank.effenberger@xxxxxxxxxxxxx>
Hi Shan, and All, In a perfect world, the equation would be: TxPower – PathLoss = Rxsensitivity. However, both transmitters and the optical path have associated penalties. The full equation is thus:
TxPower – TxPenalty – PathLoss – PathPenalty = RxSensitivity.
In the ITU specification scheme, this is rearranged as: TxPower – PathLoss – PathPenalty = (Rxsensitivity + TxPenalty) = ITUrxSensitivity.
In other words, the specified Rx sensitivity is that observed with the worst Tx possible. This has practical issues because it is making a parameter of the Rx dependent on the character of the Tx, and these are
manufactured by different companies in some cases. Also, building yourself a “worst possible transmitter” is not so easy. One might ask why this method remains popular with network operators. The answer is that it is easy to measure with simple equipment
(power meters), and the path loss is separately specified and therefore the clear responsibility of the operator. In cases where both transceivers are sourced from the same vendor, the linkage of Tx and Rx is not an issue, and even in the other case, most
optical components behave the same (we don’t expect large deviations of transmitter penalty). Bottom line, it works most of the time, and it is simple.
In the IEEE (10G) specification scheme, this is rearranged as:
(TxPower – TxPenalty – PathPenalty) – PathLoss = RxSensitivity.
Here, all the penalties are lumped into the transmitter spec (you may know it as OMA – TDP). This means that the RxSensitivity needs to be measured with a very nearly “perfect” Tx signal; for higher signaling speeds
this becomes problematic. This also has the issue that it make the Tx performance dependent on the optical path, and these are certainly manufactured by different companies. On the other hand, optical fiber is pretty consistent and well characterized. It
is relatively easy to build yourself a “worst case optical channel”. This method has the good characteristic that it allows the tradeoff between Tx power and its signal quality.
At this point, we have an aside on OMA. OMA, ER, and AveragePower are related by a simple equation:
OMA = 2*(ER-1)/(ER+1)*AveragePower. Note that is ER>>1, then OMA = 2*AveragePower, and if ER=1 (i.e., no modulation), then OMA = 0. For Johnson-noise limited receivers (PIN-detectors), the OMA is the primary signal strength indicator. This means
that by specifying the Tx OMA, we allow the tradeoff between minimum power and ER. For shot-noise limited receivers (APDs or SOA-preamp types), this is not exactly true; however, the deviations from this tradeoff are fairly small (less than a dB).
Lastly, let’s discuss TDEC (Transmitter and Dispersion Eye Closure). As mentioned above, the golden Tx needed to measure the sensitivity in the IEEE method is hard to come by for higher speeds. The TDEC method allows the measurement of
the TDP of a given transmitter by measuring its waveform digitally, and then calculating how much noise could be added until the BER limit is reached. In a sense, it is using a digital oscilloscope to simulate a “perfect receiver”. Once the Tx is characterized
(calibrated, effectively), it can then be used to measure the RxSensitivity. So, TDEC and TDECQ are really just measurement method improvements, and they do not change the basic method of OMA – TDP.
I hope that gives you an idea of the complexities involved in the specification of optical links.
A bill for my consulting services will be in the mail.
😊 Sincerely, Frank Effenberger From:
wey.junshan@xxxxxxxxx <wey.junshan@xxxxxxxxx>
Hi Frank, Yuanqiu said you would be willing to help me sort out the G.9806 vs 3cp PMD numbers. That's great. Do you have any formula used by the two groups in the past? We can have a call to discuss if it's easier. Please let me know. Thank you. Shan To unsubscribe from the STDS-802-3-NGBIDI list, click the following link:
https://listserv.ieee.org/cgi-bin/wa?SUBED1=STDS-802-3-NGBIDI&A=1 To unsubscribe from the STDS-802-3-NGBIDI list, click the following link: https://listserv.ieee.org/cgi-bin/wa?SUBED1=STDS-802-3-NGBIDI&A=1 |